|
MSDS Name
|
Uni-Spray
II Insulation Adhesive
|
|
Revision Date
|
February 1, 2010
|
|
Product Name
|
Uni-Spray
II Insulation Adhesive
|
|
CAS Number
|
none
|
|
HMIS Hazard Rating
|
Health:
2, Fire: 4, Reactivity: 0
|
|
Company
Identification |
McGill AirSeal LLC
2400 Fairwood Avenue Columbus, Ohio 43207 |
|
Contact
|
McGill AirSeal LLC
|
|
Telephone
|
(800)624-5535,
(614)829-1200
|
|
Fax
|
(614)829-1488
|
|
Chemtrec
(24-hour) |
(800)424-9300
|
|
Chemtrec
International |
(703)527-3887
|
|
Hazardous Ingredients
|
CAS Number
|
Percent
|
|
acetone
|
67-64-1
|
-
|
|
hexane
|
110-54-3
|
-
|
|
isobutane
|
75-28-5
|
-
|
|
propane
|
74-98-6
|
-
|
|
OSHA
PELs and ACGIH TL Vs are listed in Section 8 where applicable.
|
||
|
Emergency
Overview |
KEEP FROM REACH
OF CHILDREN. Do not puncture, incinerate, or place aerosol product containers in compactors.
Containers of this material may be hazardous when emptied since containers retain product residues
(vapor, liquid, and/or solid). All hazard precautions given must be observed. Do not flame cut,
braze, or use welding torch. Intentional misuse by deliberately concentrating and inhaling this
product may be harmful or fatal.
|
|
Inhalation
|
Excessive inhalation of vapors
can cause nasal and respiratory irritation, dizziness, weakness, fatigue, nausea, headache,
possible unconsciousness, and even asphyxiation. Overexposure may cause damage to the
nervous system.
|
|
Ingestion
|
No information
|
|
Skin
|
Prolonged or repeated contact can cause
moderate irritation, defatting, dermatitis.
|
|
Eye
|
Can cause severe eye irritation,
redness, tearing, blurred vision.
|
|
Chronic Hazards
|
Overexposure to this material
(or its components) has apparently been found to cause the following effects in laboratory
animals: kidney damage, eye damage, liver damage, lung damage, nasal damage, nervous system
damage, and testis damage. Overexposure to this material (or its components) has apparently been
found to cause the following effects in humans: visual impairment, central nervous
system effects.
|
|
Primary Route(s)
of Entry |
Skin contact, skin absorption,
inhalation, eye contact
|
|
Eye Contact
|
Flush with large amounts of water,
lifting upper and lower lids occasionally, get medical attention.
|
|
Skin Contact
|
Thoroughly wash exposed area with
soap and water. Remove contaminated clothing. Launder contaminated clothing before re-use. Get
medical attention if irritation persists. Mineral oil, baby oil, makeup remover, mineral spirits,
or other mild solvent may be used to remove the sticky resin residue left by the adhesive.
|
|
Inhalation
|
Remove individual to fresh air.
If breathing is difficult, administer oxygen. Give artificial respiration if breathing has
stopped. Keep person warm and quiet. Get medical attention.
|
|
Ingestion
|
Do not induce vomiting. Give two
glasses of water if conscious. Never give anything by mouth to an unconscious person. Get immediate
medical attention.
|
|
Flash Point
|
Not available.
|
|
Explosive Range
|
Lower explosive limit not available;
Upper explosive limit not available
|
|
Autoignition Temperature
|
Not determined.
|
|
Extinguishing Media
|
Use carbon dioxide, dry chemical,
foam, or water fog when fighting fires involving this product.
|
|
Unusual Fire and Explosion Hazards
|
Vapors are heavier then air and travel
along the ground or may be moved by ventilation and ignited by ignition sources at locations
distant from material handling point. For aerosol products — exposure to temperatures
over 130°F may cause containers to burst releasing highly flammable gas.
|
|
Fire-Fighting Procedures
|
Wear self-contained breathing
apparatus with a full face piece operated in pressure-demand or other positive pressure mode
when fighting fires. Keep fire-exposed containers cool with water fog.
|
|
Containment
Techniques
|
Eliminate sources of ignition and
ventilate area. Persons not properly equipped should be excluded from area. Stop spill at source
— prevent spreading. Avoid inhalation of vapors. Avoid skin contact with liquid. Soak up absorbent
material and place into proper container for disposal. Use non-sparking scoops for flammable materials.
Clean walking surfaces thoroughly to reduce slipping hazard.
|
|
Handling
|
Containers of this material may be
hazardous when emptied, since containers retain product residues (vapor, liquid, and/or solid).
All hazard precautions given must be observed. Do not flame cut, braze, or use welding torch
on containers. Intentional misuse by deliberately concentrating and inhaling the vapors from
this product may be harmful or fatal.
|
|
Storage
|
Do not store above 120°F.
Do not store in direct sunlight. Keep away from heat sources, open flame, pilot lights,
sparks, and other sources of ignition.
|
|
Occupational Exposure Limits
|
||
|
|
hexane
|
propane
|
|
ACGIH
TLV-TWA
|
50
ppm
|
1000
ppm
|
|
ACGIH
TLV-STEL
|
Not
Established
|
Not
Established
|
|
OSHA
PEL-TWA
|
50
ppm
|
1000
ppm
|
|
OSHA
PEL CEILING
|
Not
Established
|
Not
Established
|
|
COMPANY
TLV-TWA
|
Not
Established
|
Not
Established
|
|
COMPANY
Skin
|
No
|
No
|
|
|
acetone
|
isobutane
|
|
ACGIH
TLV-TWA
|
750
ppm
|
800
ppm
|
|
ACGIH
TLV-STEL
|
Not
Established
|
Not
Established
|
|
OSHA
PEL-TWA
|
1000
ppm
|
800
ppm
|
|
OSHA
PEL CEILING
|
Not
Established
|
Not
Established
|
|
COMPANY
TLV-TWA
|
Not
Established
|
Not
Established
|
|
COMPANY
Skin
|
No
|
No
|
|
Engineering Controls
|
Provide sufficient mechanical
ventilation (general and/or local exhaust) ventilation to maintain exposure below TLV(s).
|
|
Respiratory
Protection |
If work place exposure limits
of product or any component is exceeded, use a NIOSH/MSHA approved respirator. Consult your
safety equipment supplier for recommendations.
|
|
Skin Protection
|
Wear impervious gloves if method
of use involves skin contact with product. Consult your safety supply vendor for glove
recommendations.
|
|
Eye Protection
|
Wear safety glasses at minimum,
more extensive protection may be necessary depending on how the product is to be used.
|
|
Other Protective
Equipment |
Wear impervious clothing if bodily
exposure is anticipated. Consult your safety supply vendor for recommendations.
|
|
Hygenic
Practices |
Wash hands before eating or
smoking. Smoke in designated areas only. Remove and launder clothing if contaminated.
|
|
Form
|
liquid
|
|
Appearance/Color
|
straw liquid
|
|
Odor
|
mint when wet
|
|
Solubility (in water)
|
negligible
|
|
pH Value
|
not determined
|
|
Boiling Range/Point
|
not available
|
|
Freeze Point
|
not determined
|
|
Vapor Pressure
|
not determined
|
|
Coefficient of Water/Oil Distribution
|
not determined
|
|
Vapor Density
|
is heavier than air
|
|
Odor Threshold
|
not determined
|
|
Evaporation Rate
|
faster than Butyl Acetate
|
|
Specific Gravity
|
0.853
|
|
Viscosity
|
not determined
|
|
Stability
|
This product is stable under normal
storage conditions.
|
|
Hazardous
Polymerization |
Will not occur under
normal conditions.
|
|
Conditions to Avoid
|
Heat, sparks, welding arcs,
open flame, pilot lights, static electricity or other sources of ignition.
|
|
Incompatibility
|
Oxidizing agents, acids, reducing
agents, and strong oxidizers.
|
|
Hazardous
Decomposition Products |
Carbon monoxide and carbon dioxide,
various hydrocarbons, acetic acid, sulfur dioxide, nitrogen oxide, nitrogen peroxide,
sulfur monoxide.
|
|
No product or component
toxicological information is available.
|
|
No information.
|
|
Waste Disposal
|
Disposal of this product must comply
with all applicable federal, state, and local regulations.
|
|
Container Disposal
|
Disposal of this container
should comply with all applicable federal, state, and local regulations.
|
|
DOT
|
UN Number: UN1950
UN Packing Group: None Hazard Class: 2.1 Hazard Subclass: None Resp. Guide Page: 126 Shipping Name: Aerosols |
|
For domestic
ground and air shipment this product my be shipped as a Consumer Commodity ORM-D. Outer
cartons must have the ORM-D or ORM-D AIR designation. (Our original cartons are preprinted
with the ORM-D designation for ground shipment).
|
|
|
OSHA
|
|
Hazardous by definition of
Hazard Communication Standard (29 CFR 1910.1200).
|
|
CERCLA - SARA Hazard Category
|
|
|
This product has been reviewed
according to the EPA "Hazard Categories" promulgated under Sections 311 and 312
of the Superfund Amendment and Reauthorization Act of 1986 (SARA Title III) and is considered,
under applicable definitions, to meet the following categories:
IMMEDIATE HEALTH HAZARD, CHRONIC HEALTH HAZARD, FIRE HAZARD, PRESSURIZED GAS HAZARD |
|
SARA Section Title 313
|
|
|
This product contains the
following substances subject to the reporting requirements of Section 313 of Title III
of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372:
|
|
Chemical Name
|
CAS Number
|
Wt/Wt % is Less Than
|
|
hexane
|
110-54-3
|
—
|
|
Toxic Substances Control Act
|
|
|
This product contains the following
substances subject to the reporting requirements of TSCA 12 (B) if exported from the United
States:
|
|
Chemical Name
|
CAS Number
|
Wt/Wt % is Less Than
|
|
No
information is available
|
—
|
—
|
|
International Regulations
|
|
Canadian WHMIS: This MSDS has
been prepared in compliance with Controlled Product Regulations except for use of the 16 headings.
|
|
Canadian WHMIS Class: No
information available.
Hexane is a mixture of n-hexane and other compounds all falling under the general chemical name light hydrotreated distillate CAS-68410-97-9. The n-hexane content of our hexane is 60 to 70 percent. On June 30, 1993 the OSHA Z-1-A table was revoked and OSHA reverted back to their prior exposure limits. The values on this MSDS reflect the roll back to the prior values. Some states may continue to enforce the 1993 limits. On June 16, 1995 EPA announced in a final rule that acetone would no longer be considered a VOC for air attainment standards (it is now an exempt compound). The VOC calculations on this MSDS are based on acetone being an exempt compound. The June 16 rule also removed acetone from the list of SARA 313 reportable chemicals. |
|
Disclaimer
|
The information contained on this
MSDS has been checked and should be accurate. However, it is the responsibility of the user to
comply with all Federal, State, and Local laws and regulations. The environmental information
and hazardous materials identification system have been included by McGill AirSeal LLC in order
to provide additional health and hazard classification information. The ratings recommended are
based upon the criteria supplied by the developers of these rating systems, together with McGill
AirSeal LLC's interpretation of the available data. Proper personal protective equipment varies widely
with conditions of use and anticipated exposure. We recommend that a supervisor or other qualified
person determine proper PPE for intended use.
|
|
HMIS Ratings
|
Health: 2; Flammability: 4;
Reactivity: 0
|
|
Previous MSDS Revision Date
|
3/01/03
|
|
Reason for Revision
|
Scheduled update
|
©
Copyright 2001-2011 McGill AirSeal LLC
e-mail us: sales@mcgillairseal.com
An
enterprise of United McGill Corporation—Family owned and operated since 1951
All the trademarks (™) and registered trademarks (®) in this
Web site are the property of United McGill Corporation.